SAFETY DATA SHEET
DOW AGROSCIENCES S.A.S.

Product name: ABIR™ 250SC Fungicide	Issue Date: 03/05/2018Print Date: 03/05/2018	
DOW AGROSCIENCES S.A.S. encourages and expects you to read and understand the entire (M)SDS, as there is important information throughout the document.  We expect you to follow the precautions identified in this document unless your use conditions would necessitate other appropriate methods or actions.

1. PRODUCT AND COMPANY IDENTIFICATION
Product name: ABIR™ 250SC Fungicide

Recommended use of the chemical and restrictions on use
Identified uses: Plant Protection Product  Fungicide  

COMPANY IDENTIFICATION
DOW AGROSCIENCES S.A.S.
371, RUE LUDWIG VAN BEETHOVEN
06560 VALBONNE
FRANCE

Customer Information Number:(0) 493 95 60 00
SDSQuestion@dow.com
Emergency telephone number
24-Hour Emergency Contact: 0033 388 736 000
Local Emergency Contact: 00 31 115 69 4982

2. HAZARDS IDENTIFICATION

Classification of the substance or mixture
Skin sensitisation - Category 1 - H317
Acute aquatic toxicity - Category 1 - H400
Chronic aquatic toxicity - Category 1 - H410
For the full text of the H-Statements mentioned in this Section, see Section 16.

Label elements

Hazard pictograms

Signal word: Warning

Hazard statements
H317	May cause an allergic skin reaction.	H410	Very toxic to aquatic life with long lasting effects.	
Precautionary statements
P280	Wear protective gloves/ protective clothing.	P302 + P352	IF ON SKIN: Wash with plenty of soap and water.	P391	Collect spillage.	P501	Dispose of contents/container in accordance with applicable regulations.	
Supplemental information
EUH401	To avoid risks to human health and the environment, comply with the instructions for use.			
ContainsQuinoxyfen

Other hazards
No data available
3. COMPOSITION/INFORMATION ON INGREDIENTS

This product is a mixture.
CASRN / 
EC-No. / 
Index-No.Concentration	Component	Classification	CASRN
124495-18-7
EC-No.
Not available
Index-No.
613-138-00-7	22.58%	Quinoxyfen	Skin Sens. - 1 - H317
Aquatic Acute - 1 - H400
Aquatic Chronic - 1 - H410
	CASRN
57-55-6
EC-No.
200-338-0
Index-No.
 – 	< 10.0 %	Propylene glycol	Not classified	For the full text of the H-Statements mentioned in this Section, see Section 16.

4. FIRST AID MEASURES
Description of first aid measures
General advice: First Aid responders should pay attention to self-protection and use the recommended protective clothing (chemical resistant gloves, splash protection).  If potential for exposure exists refer to Section 8 for specific personal protective equipment.  

Inhalation: Move person to fresh air. If person is not breathing, call an emergency responder or ambulance, then give artificial respiration; if by mouth to mouth use rescuer protection (pocket mask etc). Call a poison control center or doctor for treatment advice.  

Skin contact: Take off contaminated clothing. Wash skin with soap and plenty of water for 15-20 minutes. Call a poison control center or doctor for treatment advice.  Wash clothing before reuse. Shoes and other leather items which cannot be decontaminated should be disposed of properly.  

Eye contact: Hold eyes open and rinse slowly and gently with water for 15-20 minutes. Remove contact lenses, if present, after the first 5 minutes, then continue rinsing eyes. Call a poison control center or doctor for treatment advice.  

Ingestion: No emergency medical treatment necessary.  

Most important symptoms and effects, both acute and delayed: Aside from the information found under Description of first aid measures (above) and Indication of immediate medical attention and special treatment needed (below), any additional important symptoms and effects are described in Section 11: Toxicology Information.

Indication of any immediate medical attention and special treatment needed
Notes to physician: No specific antidote.  Treatment of exposure should be directed at the control of symptoms and the clinical condition of the patient.  Have the Safety Data Sheet, and if available, the product container or label with you when calling a poison control center or doctor, or going for treatment.  

5. FIREFIGHTING MEASURES
Suitable extinguishing media: To extinguish combustible residues of this product use water fog, carbon dioxide, dry chemical or foam.  Alcohol resistant foams (ATC type) are preferred. General purpose synthetic foams (including AFFF) or protein foams may function, but will be less effective.  

Unsuitable extinguishing media: No data available

Special hazards arising from the substance or mixture
Hazardous combustion products: Under fire conditions some components of this product may decompose. The smoke may contain unidentified toxic and/or irritating compounds.  Combustion products may include and are not limited to:  Nitrogen oxides.  Hydrogen fluoride.  Hydrogen chloride.  Carbon monoxide.  Carbon dioxide.  

Unusual Fire and Explosion Hazards: This material will not burn until the water has evaporated. Residue can burn.    

Advice for firefighters
Fire Fighting Procedures: Keep people away.  Isolate fire and deny unnecessary entry.  Use water spray to cool fire exposed containers and fire affected zone until fire is out and danger of reignition has passed.  Burning liquids may be extinguished by dilution with water.  Burning liquids may be moved by flushing with water to protect personnel and minimize property damage.  To extinguish combustible residues of this product use water fog, carbon dioxide, dry chemical or foam.  Contain fire water run-off if possible. Fire water run-off, if not contained, may cause environmental damage.  Review the "Accidental Release Measures" and the "Ecological Information" sections of this (M)SDS.  

Special protective equipment for firefighters: Wear positive-pressure self-contained breathing apparatus (SCBA) and protective fire fighting clothing (includes fire fighting helmet, coat, trousers, boots, and gloves).  Avoid contact with this material during fire fighting operations. If contact is likely, change to full chemical resistant fire fighting clothing with self-contained breathing apparatus.  If this is not available, wear full chemical resistant clothing with self-contained breathing apparatus and fight fire from a remote location.  For protective equipment in post-fire or non-fire clean-up situations, refer to the relevant sections.  

6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures: Use appropriate safety equipment. For additional information, refer to Section 8, Exposure Controls and Personal Protection.  

Environmental precautions: Prevent from entering into soil, ditches, sewers, waterways and/or groundwater. See Section 12, Ecological Information.  Spills or discharge to natural waterways is likely to kill aquatic organisms.  

Methods and materials for containment and cleaning up: Contain spilled material if possible.  Small spills:  Absorb with materials such as:  Clay.  Dirt.  Sand.  Sweep up.  Collect in suitable and properly labeled containers.  Large spills:  Contact Dow AgroSciences for clean-up assistance.  See Section 13, Disposal Considerations, for additional information.  

7. Handling and storage
Precautions for safe handling: Keep out of reach of children.  Keep away from heat, sparks and flame.  Do not swallow.  Avoid contact with eyes, skin, and clothing.  Avoid breathing vapor or mist.  Avoid prolonged or repeated contact with skin.  Wash thoroughly after handling.  Use with adequate ventilation.  Containers, even those that have been emptied, can contain vapors. Do not cut, drill, grind, weld, or perform similar operations on or near empty containers.  See Section 8, EXPOSURE CONTROLS AND PERSONAL PROTECTION.  

Conditions for safe storage: Store in a dry place.  Store in original container.  Keep container tightly closed when not in use.  Do not store near food, foodstuffs, drugs or potable water supplies.  

8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Control parameters
If exposure limits exist, they are listed below.  If no exposure limits are displayed, then no values are applicable.
Component	Regulation	Type of listing	Value/Notation	Quinoxyfen	Dow IHG	TWA 	5 mg/m3  		Dow IHG	TWA 	   Skin Sensitizer	Propylene glycol	US WEEL	TWA 	10 mg/m3  	
RECOMMENDATIONS IN THIS SECTION ARE FOR MANUFACTURING, COMMERCIAL BLENDING AND PACKAGING WORKERS. APPLICATORS AND HANDLERS SHOULD SEE THE PRODUCT LABEL FOR PROPER PERSONAL PROTECTIVE EQUIPMENT AND CLOTHING.  

Exposure controls
Engineering controls: Use local exhaust ventilation, or other engineering controls to maintain airborne levels below exposure limit requirements or guidelines.  If there are no applicable exposure limit requirements or guidelines, general ventilation should be sufficient for most operations.  Local exhaust ventilation may be necessary for some operations.  

Individual protection measures
Eye/face protection: Use safety glasses (with side shields).  Safety glasses (with side shields) should be consistent with EN 166 or equivalent.  
Skin protection
Hand protection: Use chemical resistant gloves classified under Standard EN374: Protective gloves against chemicals and micro-organisms.  Examples of preferred glove barrier materials include:  Chlorinated polyethylene.  Neoprene.  Polyethylene.  Ethyl vinyl alcohol laminate ("EVAL").  Viton.  Examples of acceptable glove barrier materials include:  Butyl rubber.  Natural rubber ("latex").  Nitrile/butadiene rubber ("nitrile" or "NBR").  Polyvinyl chloride ("PVC" or "vinyl").  When prolonged or frequently repeated contact may occur, a glove with a protection class of 5 or higher (breakthrough time greater than 240 minutes according to EN 374) is recommended.  When only brief contact is expected, a glove with a protection class of 3 or higher (breakthrough time greater  than 60 minutes according to EN 374) is recommended.  NOTICE: The selection of a specific glove for a particular application and duration of use in a workplace should also take into account all relevant workplace factors such as, but not limited to: Other chemicals which may be handled, physical requirements (cut/puncture protection, dexterity, thermal protection), potential body reactions to glove materials, as well as the instructions/specifications provided by the glove supplier.  
Other protection: Use protective clothing chemically resistant to this material.  Selection of specific items such as face shield, boots, apron, or full body suit will depend on the task.  
Respiratory protection: Respiratory protection should be worn when there is a potential to exceed the exposure limit requirements or guidelines.  If there are no applicable exposure limit requirements or guidelines, wear respiratory protection when adverse effects, such as respiratory irritation or discomfort have been experienced, or where indicated by your risk assessment process.  For most conditions no respiratory protection should be needed;  however, if discomfort is experienced, use an approved air-purifying respirator.  
Use the following CE approved air-purifying respirator:  Organic vapor cartridge with a particulate pre-filter, type AP2.  

See SECTION 7: Handling and storage and SECTION 13: Disposal considerations for measures to prevent excessive environmental exposure during use and waste disposal.

9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance
Physical state	Liquid.  	ColorOff-white  Odor	Faint earthy odor  	Odor Threshold	No test data available  	pH	8.0   1% pH Electrode (1% aqueous suspension)Melting point/range	Not applicableFreezing point	No test data availableBoiling point (760 mmHg)	No test data availableFlash point	closed cup > 93.3 °C Setaflash Closed Cup ASTM D3828 Evaporation Rate (Butyl Acetate = 1)	No test data availableFlammability (solid, gas)	No data available  Lower explosion limit	No test data available  Upper explosion limit	No test data available  Vapor Pressure	 No test data availableRelative Vapor Density (air = 1)	No test data available 	Relative Density (water = 1)	No data available	Water solubility	No test data available  	Partition coefficient: n-octanol/water	No data available  	Auto-ignition temperature	No test data available  	Decomposition temperature	No test data available  	Dynamic Viscosity	130 mPa.s 	Kinematic Viscosity	117 mm2/s 	Explosive properties	No 	Oxidizing properties	No significant increase (>5C) in temperature. 	Liquid Density	1.11 g/cm3 at 21 °C Digital density meter 	Molecular weight	No data available	
NOTE:  The physical data presented above are typical values and should not be construed as a specification.
10. STABILITY AND REACTIVITY
Reactivity: No dangerous reaction known under conditions of normal use.  

Chemical stability: Stable under recommended storage conditions.  See Storage, Section 7.  

Possibility of hazardous reactions: Polymerization will not occur.  
 
Conditions to avoid: Active ingredient decomposes at elevated temperatures.  Generation of gas during decomposition can cause pressure in closed systems.  

Incompatible materials: Avoid contact with:  Strong acids.  Strong bases.  Strong oxidizers.  

Hazardous decomposition products:  Decomposition products depend upon temperature, air supply and the presence of other materials.  Decomposition products can include and are not limited to:  Hydrogen chloride.  Hydrogen fluoride.  Nitrogen oxides.  
11. TOXICOLOGICAL INFORMATION

Toxicological information appears in this section when such data is available. 

Acute toxicity
Acute oral toxicity
Very low toxicity if swallowed.  Harmful effects not anticipated from swallowing small amounts.  

As product:  Single dose oral LD50 has not been determined.  

For similar material(s):  
LD50. Rat. > 5,000 mg/kg  No deaths occurred at this concentration.  

Acute dermal toxicity
Prolonged skin contact is unlikely to result in absorption of harmful amounts.  

As product:  The dermal LD50 has not been determined.  

For similar material(s):  
LD50. Rat. > 2,000 mg/kg No deaths occurred at this concentration.  

Acute inhalation toxicity
No adverse effects are anticipated from single exposure to mist.  Based on the available data, respiratory irritation was not observed.  
As product:  The LC50 has not been determined.  

Skin corrosion/irritation
Brief contact is essentially nonirritating to skin.

Serious eye damage/eye irritation
Essentially nonirritating to eyes.

Sensitization
For the active ingredient(s):
Has caused allergic skin reactions when tested in guinea pigs.
For similar material(s):
Did not demonstrate the potential for contact allergy in mice.

For respiratory sensitization:
No relevant information found.

Specific Target Organ Systemic Toxicity (Single Exposure)
Evaluation of available data suggests that this material is not an STOT-SE toxicant.

Specific Target Organ Systemic Toxicity (Repeated Exposure)
For the active ingredient(s):
In animals, effects have been reported on the following organs:
Kidney.
Liver.
Blood.

Carcinogenicity
For the active ingredient(s):  Did not cause cancer in laboratory animals.  

Teratogenicity
For the active ingredient(s):  Did not cause birth defects or other effects in the fetus even at doses which caused toxic effects in the mother.  

Reproductive toxicity
For the active ingredient(s):  In animal studies, did not interfere with reproduction.  

Mutagenicity
For the active ingredient(s):  In vitro genetic toxicity studies were negative.  Animal genetic toxicity studies were negative.  

Aspiration Hazard
Based on physical properties, not likely to be an aspiration hazard.  

Components influencing toxicology:
 
Quinoxyfen
Acute inhalation toxicity 
No adverse effects are anticipated from single exposure to mist.  Based on the available data, narcotic effects were not observed.  Based on the available data, respiratory irritation was not observed.  
 
Maximum attainable concentration.  LC50. Rat. male and female. 4 Hour. dust/mist. > 3.38 mg/l No deaths occurred at this concentration.  
 
Propylene glycol
Acute inhalation toxicity 
Mist may cause irritation of upper respiratory tract (nose and throat).  LC50. Rabbit. 2 Hour. dust/mist. 317.042 mg/l No deaths occurred at this concentration.  

12. ECOLOGICAL INFORMATION

Ecotoxicological information appears in this section when such data is available.

Toxicity
Acute toxicity to fish
Material is very toxic to aquatic organisms (LC50/EC50/IC50 below 1 mg/L in the most sensitive species).

For similar material(s):
LC50. Oncorhynchus mykiss (rainbow trout). 96 Hour. > 100 mg/l

Acute toxicity to aquatic invertebrates
For similar material(s):
EC50. Daphnia magna (Water flea). 48 Hour. 0.2 mg/l

Acute toxicity to algae/aquatic plants
For similar material(s):
ErC50. Pseudokirchneriella subcapitata (green algae). 72 Hour. 0.28 mg/l

Toxicity to soil-dwelling organisms
LC50. Eisenia fetida (earthworms). 14 d. > 1,000 mg/kg

Persistence and degradability

Quinoxyfen
Biodegradability: Based on stringent OECD test guidelines, this material cannot be considered as readily biodegradable; however, these results do not necessarily mean that the material is not biodegradable under environmental conditions.  
10-day Window: Fail  
Biodegradation:  2 - 3 % 
Exposure time: 28 d 
Method: OECD Test Guideline 301B or Equivalent  

Stability in Water (1/2-life)
Hydrolysis. half-life. > 1 year

Photodegradation
Atmospheric half-life: 1.88 d

Propylene glycol
Biodegradability: Material is readily biodegradable.  Passes OECD test(s) for ready biodegradability.  Biodegradation may occur under anaerobic conditions (in the absence of oxygen).  
10-day Window: Pass  
Biodegradation:  81 % 
Exposure time: 28 d 
Method: OECD Test Guideline 301F or Equivalent  
10-day Window: Not applicable  
Biodegradation:  96 % 
Exposure time: 64 d 
Method: OECD Test Guideline 306 or Equivalent  

Bioaccumulative potential

Quinoxyfen
Bioaccumulation: Bioconcentration potential is high (BCF > 3000 or Log Pow between 5 and 7).  
Partition coefficient: n-octanol/water(log Pow): 4.66 Measured 
Bioconcentration factor (BCF): 5,040  Fish    Measured

Propylene glycol
Bioaccumulation: Bioconcentration potential is low (BCF < 100 or Log Pow < 3).  
Partition coefficient: n-octanol/water(log Pow): -1.07 Measured 
Bioconcentration factor (BCF): 0.09      Estimated.

Mobility in soil

Quinoxyfen
Expected to be relatively immobile in soil (Koc > 5000).
Partition coefficient (Koc): 22929 Estimated.

Propylene glycol
Given its very low Henry's constant, volatilization from natural bodies of water or moist soil is not expected to be an important fate process.
Potential for mobility in soil is very high (Koc between 0 and 50).
Partition coefficient (Koc): < 1 Estimated.

Results of PBT and vPvB assessment 

Quinoxyfen
This substance has not been assessed for persistence, bioaccumulation and toxicity  (PBT).  

Propylene glycol
This substance is not considered to be persistent, bioaccumulating and toxic (PBT).  This substance is not considered to be very persistent and very bioaccumulating (vPvB).  

Other adverse effects

Quinoxyfen
This substance is not on the Montreal Protocol list of substances that deplete the ozone layer.

Propylene glycol
This substance is not on the Montreal Protocol list of substances that deplete the ozone layer.

13. DISPOSAL CONSIDERATIONS
Disposal methods: 
If wastes and/or containers cannot be disposed of according to the product label directions, disposal of this material must be in accordance with your local or area regulatory authorities.  This information presented below only applies to the material as supplied.  The identification based on characteristic(s) or listing may not apply if the material has been used or otherwise contaminated.  It is the responsibility of the waste generator to determine the toxicity and physical properties of the material generated to determine the proper waste identification and disposal methods in compliance with applicable regulations.  If the material as supplied becomes a waste, follow all applicable regional, national and local laws.  

14. TRANSPORT INFORMATION

Classification for ROAD and Rail transport:
Proper shipping name	ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.(Quinoxyfen)	UN number	UN  3082	Class	9	Packing group	III	Environmental hazards	Quinoxyfen	

Classification for SEA transport (IMO-IMDG):
Proper shipping name	ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.(Quinoxyfen)	UN number	UN  3082	Class	9	Packing group	III	Marine pollutant	Quinoxyfen	Transport in bulk according to Annex I or II of MARPOL 73/78 and the IBC or IGC Code	Consult IMO regulations before transporting ocean bulk	
Classification for AIR transport (IATA/ICAO):
Proper shipping name	Environmentally hazardous substance, liquid, n.o.s.(Quinoxyfen)	UN number	UN  3082	Class	9	Packing group	III	

This information is not intended to convey all specific regulatory or operational requirements/information relating to this product.  Transportation classifications may vary by container volume and may be influenced by regional or country variations in regulations.  Additional transportation system information can be obtained through an authorized sales or customer service representative.  It is the responsibility of the transporting organization to follow all applicable laws, regulations and rules relating to the transportation of the material.

15. REGULATORY INFORMATION

Seveso III: Directive 2012/18/EU of the European Parliament and of the Council on the control of major-accident hazards involving dangerous substances.
Listed in Regulation: ENVIRONMENTAL HAZARDS
Number in Regulation: E1
100 t
200 t

Classification and labeling have been performed according to Regulation (EC) No 1272/2008.
16. OTHER INFORMATION

Full text of H-Statements referred to under sections 2 and 3.
H317May cause an allergic skin reaction.	H400Very toxic to aquatic life.	H410Very toxic to aquatic life with long lasting effects.	
Revision
Identification Number: 96884 / A285 / Issue Date: 03/05/2018 / Version: 4.0
DAS Code: EF-1295
Most recent revision(s) are noted by the bold, double bars in left-hand margin throughout this document.

Legend
Dow IHG	Dow Industrial Hygiene Guideline	TWA	8-hr TWA	US WEEL	USA. Workplace Environmental Exposure Levels (WEEL)	Aquatic Acute	Acute aquatic toxicity	Aquatic Chronic	Chronic aquatic toxicity	Skin Sens.	Skin sensitisation	
Full text of other abbreviations
ADN - European Agreement concerning the International Carriage of Dangerous Goods by Inland Waterways; ADR - European Agreement concerning the International Carriage of Dangerous Goods by Road; AICS - Australian Inventory of Chemical Substances; ASTM - American Society for the Testing of Materials; bw - Body weight; CLP - Classification Labelling Packaging Regulation; Regulation (EC) No 1272/2008; CMR - Carcinogen, Mutagen or Reproductive Toxicant; DIN - Standard of the German Institute for Standardisation; DSL - Domestic Substances List (Canada); ECHA - European Chemicals Agency; EC-Number - European Community number; ECx - Concentration associated with x% response; ELx - Loading rate associated with x% response; EmS - Emergency Schedule; ENCS - Existing and New Chemical Substances (Japan); ErCx - Concentration associated with x% growth rate response; GHS - Globally Harmonized System; GLP - Good Laboratory Practice; IARC - International Agency for Research on Cancer; IATA - International Air Transport Association; IBC - International Code for the Construction and Equipment of Ships carrying Dangerous Chemicals in Bulk; IC50 - Half maximal inhibitory concentration; ICAO - International Civil Aviation Organization; IECSC - Inventory of Existing Chemical Substances in China; IMDG - International Maritime Dangerous Goods; IMO - International Maritime Organization; ISHL - Industrial Safety and Health Law (Japan); ISO - International Organisation for Standardization; KECI - Korea Existing Chemicals Inventory; LC50 - Lethal Concentration to 50 % of a test population; LD50 - Lethal Dose to 50% of a test population (Median Lethal Dose); MARPOL - International Convention for the Prevention of Pollution from Ships; n.o.s. - Not Otherwise Specified; NO(A)EC - No Observed (Adverse) Effect Concentration; NO(A)EL - No Observed (Adverse) Effect Level; NOELR - No Observable Effect Loading Rate; NZIoC - New Zealand Inventory of Chemicals; OECD - Organization for Economic Co-operation and Development; OPPTS - Office of Chemical Safety and Pollution Prevention; PBT - Persistent, Bioaccumulative and Toxic substance; PICCS - Philippines Inventory of Chemicals and Chemical Substances; (Q)SAR - (Quantitative) Structure Activity Relationship; REACH - Regulation (EC) No 1907/2006 of the European Parliament and of the Council concerning the Registration, Evaluation, Authorisation and Restriction of Chemicals; RID - Regulations concerning the International Carriage of Dangerous Goods by Rail; SADT - Self-Accelerating Decomposition Temperature; SDS - Safety Data Sheet; TCSI - Taiwan Chemical Substance Inventory; TSCA - Toxic Substances Control Act (United States); UN - United Nations; UNRTDG - United Nations Recommendations on the Transport of Dangerous Goods; vPvB - Very Persistent and Very Bioaccumulative

Information Source and References
This SDS is prepared by Product Regulatory Services and Hazard Communications Groups from information supplied by internal references within our company.

DOW AGROSCIENCES S.A.S. urges each customer or recipient of this (M)SDS to study it carefully and consult appropriate expertise, as necessary or appropriate, to become aware of and understand the data contained in this (M)SDS and any hazards associated with the product.  The information herein is provided in good faith and believed to be accurate as of the effective date shown above.  However, no warranty, express or implied, is given.  Regulatory requirements are subject to change and may differ between various locations. It is the buyer's/user's responsibility to ensure that his activities comply with all federal, state, provincial or local laws.  The information presented here pertains only to the product as shipped.  Since conditions for use of the product are not under the control of the manufacturer, it is the buyer's/user's duty to determine the conditions necessary for the safe use of this product.  Due to the proliferation of sources for information such as manufacturer-specific (M)SDSs, we are not and cannot be responsible for (M)SDSs obtained from any source other than ourselves.  If you have obtained an (M)SDS from another source or if you are not sure that the (M)SDS you have is current, please contact us for the most current version.    

IL